La Cumbre FloorCovering & Design · Lic. #1125785 Español (805) 698-9745
Skip tour
Santa Barbara & Ventura CountiesLic. #1125785

Most worn hardwood floors can be saved.

We sand, repair, color-match and finish, and we lay new floors. And we’ll tell you straight whether yours can be saved. Scroll to watch this one come back.

Call or text Mon–Sat, 8 am to 10 pm5.0 on Google, 53 reviewsA+ BBB accreditedFree estimates
Step 01Repair

First, the boards that can't be saved.

Termite-eaten and water-damaged boards come out one at a time. New ones are woven into the old rows, board by board, so the repair runs with the floor and doesn't read as a patch.

Board replacement · Termite damage · Subfloor repair

A floor opened to the joists, with the level laid across.
Step 02Sand

Then down to bare wood.

Sanding takes off the old finish, the gray and the scratches, and shows what's really under there. On this floor, white oak on the left and red oak on the right.

Oak · Douglas-fir · Parquet

Every knot filled, and the sander ready.
Step 03Color

Two woods, one color.

Red oak runs pink and white oak runs tan, so one stain lands differently on each. We balance them with custom stain, bleaching and color matching until they blend. Pick a tone:

Tone: Walnut

Ten stain samples, taped off on the customer's own floor.
“We had new floors old floors to match up and stain. They worked efficiently and the results are fantastic.”Daniel L. · Google review
Step 04Finish

Finish coats, tape off, furniture back.

The finish seals the color and takes the daily wear. Furniture goes back three days after the last coat, rugs after 30. The last thing to leave is the blue tape on your baseboards. That’s the day the job is done.

The day the tape came off.
5.0 on Google53 reviews
#1125785Licensed and insured
18 yearsHands-on with hardwood
Free estimatesWe usually come out in 1 to 3 days
EspañolHablamos español
Can it be saved?

Check your floor in a minute.

Three questions. Answer them standing over the floor. The rules come from our refinishing and repair guides.

1What kind of floor is it?
2At a floor vent or a doorway edge, how thick is the top layer of wood?
3What do you see? Check all that apply.

What it likely needs

A recoat may be enough

  • Solid wood with about 1/4 inch of wear layer can usually be sanded six to eight times.
  • Dull finish and light scratches: screen and recoat, or a polish and top coat.

The repair guide has a table of what each problem needs, and the refinishing guide explains how to check the thickness.

Text us three photos

  1. The whole room, from the doorway
  2. The edge at a vent or doorway, close up
  3. The worst spot

We'll tell you for sure when we see it. The estimate is free.

On the job

Fourteen photos, in the order the work happens.

These are our own job photos, from the day the old floor comes up to the day the finish dries. Different houses, same order. Keep scrollingSwipe sideways

  1. A hand peels back old flooring in a corner to show dark, crumbling material underneath
    01 Open it upPull back the old floor and this is sometimes what is under it. Better to find it now than after the new floor is down.
  2. A bare subfloor beside an iron stair rail, with a patch of metal mesh and a long straightedge on the ground
    02 Tear-outOld floor out. The subfloor gets checked with a straightedge before anything goes on top.
  3. A floor opened down to the joists, with spray foam between them, plywood pieces, tools and a long level laid across
    03 Subfloor repairOpened to the joists. New plywood goes down and the level tells us when it is flat.
  4. Two crew members with a floor machine and vacuum hose take old black adhesive off a plywood subfloor
    04 Clean the baseOld adhesive ground off the plywood, with the vacuum running the whole time.
  5. A crew member kneels and holds a six-foot level over a low spot marked on a slab
    05 Check for flatA long level over the slab finds the low spots. They get marked and filled.
  6. Wet gray leveling compound spreads across a room around a patch of old slab, with an empty bucket in the middle
    06 Level the slabLeveling compound poured across the room. It flows flat and sets hard.
  7. A gloved hand combs white adhesive into ridges with a notched trowel, next to the last row of planks
    07 GlueAdhesive combed out with a notched trowel, one row at a time, right up to the last plank laid.
  8. Two crew members fit border boards on the floor at the foot of a stair with an iron railing, tools and adhesive around them
    08 LayBorder boards fitted at the foot of a stair. The edges go in first so the field has something square to meet.
  9. A pale new plank floor dotted with dark filler patches, with a drum sander in the foreground
    09 Fill and sandEvery knot and crack filled dark, then the sander takes the floor flat.
  10. Ten stain samples in different browns, grays and a red, each boxed in blue tape on a sanded floor
    10 Choose the colorStain samples on your own floor, taped off and labeled. You choose in your own light.
  11. A wide applicator on a pole spreads a milky first coat down a run of pale new boards, with a bucket beside it
    11 First coatFirst coat going down along the boards.
  12. A crew member in a black cap kneels and wipes a floor with a rag, working toward the kitchen
    12 By handWiped by hand, board by board, on his knees.
  13. A front porch floor stained very dark and still wet with finish, with blue tape along the door sill
    13 FinishFinish going on. The last coat is still wet, and the blue tape stays until it is dry.
  14. A paneled room with wide plank flooring reflecting three French doors, and a herringbone floor in the doorway in front
    14 DoneDone. Wide planks in the room, herringbone in the doorway.
Finished floors

What it looks like when the tape comes off.

Twelve rooms from our own jobs: refinished oak, wide plank, herringbone and dark stain. Custom Floors Crafted With Passion is our motto.

A long gallery with a dark stained oak floor, arched glass doors on both sides and a wood door at the end
Dark stain on oak, down a gallery of arched doors.
A white room with dark beams, an iron chandelier and an arched doorway, and a pale natural wood floor
Pale natural finish under dark beams.
A curved stair seen from above, each wedge-shaped tread covered in gray-brown wood
A curved stair. Every tread is a different wedge.
A white kitchen and hall with a floor of gray-toned wood planks
Gray-toned planks through a kitchen.
A freshly coated floor mirrors a wall of glass doors that look out over a garden to the ocean
Wet finish, glass doors, the ocean behind them.
A wide plank floor with strong dark grain and a satin shine, in a room with wood-paneled cabinets and glass doors
Wide dark planks with the grain left to show.
A herringbone floor with a dark inlaid line that steps around the base of a wall
Herringbone with a dark inlaid border that follows the wall.
A long room of mixed-tone wide planks with a full wall of glass doors on a garden
Mixed-tone wide planks along a wall of glass.
A vaulted room with dark beams and a fireplace, seen from a step down onto a light plank floor
A light plank floor in a vaulted room.
A refinished oak floor with a high gloss runs through an opening to a wall of windows on a garden
Refinished oak with a high gloss, out to the garden windows.
Light oak stair treads with scalloped white tile on the risers, turning at a landing
New treads at a landing, with scalloped tile on the risers.
A furnished living room with a light natural wide plank floor, a gray sectional and a fireplace
A natural wide plank floor, lived on.
Floors on the South Coast

What we find in South Coast houses.

Old fir under carpet, oak that changes halfway down the hall, termites, concrete slabs. The houses here are old, and their floors show it.

  • Old Douglas-fir

    Older houses often have Douglas-fir floors. Fir is softer than oak and needs a lighter hand on the sander. We sand and refinish it in place.

  • Two oaks in one house

    Additions and past repairs leave red oak next to white oak. We tint the color so the rooms read as one floor.

  • Termite damage

    We cut out the eaten boards, repair what's under them and lace in new wood before sanding.

  • Scratches and worn finish

    Deep scratches get touched up. A dull floor gets polished or a fresh top coat.

  • Concrete slabs

    We test the slab for moisture, level it and prepare it so the new floor has a sound base. Or we polish the concrete itself.

Timing

4to7days to refinish one to three rooms

Furniture back in three days. Rugs in thirty.

Counted from the last coat, so the finish can cure. We come out to look usually within one to three days of your call, and the estimate is free. The smallest job we take is a single scratch touch-up.

Services

Wood floors, plus the work under and around them.

One licensed crew for the tear-out, the prep, the floor and the finish.

Wood floors

Prep and other floors

Baseboards too. Not tile, decks or stair railings.

Garage floors, too.

Flake epoxy, sealed under a clear coat. See the finished garages

Try a pattern

Lay it out before we lay it down.

Pick one of nine patterns and nine tones to see the direction, then tell us what you chose. We'll tell you what your wood and your room can do.

Herringbone · Walnut

Screen colors are close, not exact. We test stain on your own floor.

Pattern
Tone
Sheen

Afternoon light, satin: about 15 to 25 percent gloss.

Then plan it.

Pick the job, the rooms and the week you'd like. The dates use La Cumbre Floor's own timing.

The job
Rooms
  1. We come to lookUsually 1 to 3 daysafter you text or call
  2. The work4 to 7 daysto refinish one to three rooms
  3. Furniture back3 days laterafter the last coat
  4. Rugs down30 days laterafter the last coat

Typical timing for one to three rooms. We set real dates once we’ve seen your floor.

“Hi La Cumbre, I'd like my floor refinished in a walnut tone (herringbone pattern), 2 rooms.”

See the real floors

Job photos and videos are on Instagram: sanding, repairs, stairs and finished rooms.

@la_cumbre_floor on Instagram
How a job runs

The same four steps, on your floor.

It starts with a free estimate. We usually come out within one to three days, look at the floor and walk you through your options.

  1. Prep

    Carpet or old flooring comes out. Baseboards get taped.

  2. Repair and sand

    Damaged boards and subfloor fixed, then everything goes down to bare wood.

  3. Color

    Stain or tint to the tone you chose, blended across any mixed woods.

  4. Finish

    Top coats, tape off, and the room is yours again.

“The hardest part is when there's a gap between a client's vision and the final result. That's why we focus heavily on clear communication and physical samples early on, to ensure we exceed their expectations every time.”La Cumbre Floor

Every step, from your first call to the last coat and after

For builders, designers and property managers

“I will continue to use and refer Tony & his team any chance I get.”

Chris H., Santa Barbara real estate broker · Google review

Call with the address, the square footage and the date the room is clear.

Licensed and insured

California contractor license #1125785, class C-15 Flooring and Floor Covering, with general liability insurance and workers’ compensation. Check it with the state license board.

Accredited

Better Business Bureau accredited since September 2024, rated A+.

Two languages

English and Spanish spoken.

Call (805) 698-9745
Reviews
“Tony and his crew jumped in with no notice and completed a beautiful floor repair for us in a day and half so that we could get our house on the market. We had been waiting on another flooring company for over a month.”Christina · Google review
5.0 on Google

5.0 on Google from 53 reviews and 5.0 on Yelp from 5, as of October 2026. Here are a few, with our replies.

“TONY, and his crew were great. Always on time and kept us updated on their every progress. We had moisture damaged to our dining area and hallway. He pointed out small details that other floor contractors failed to recognize. Luis and his crew replaced our dining and hallway area, sand and finished the rest of the house to match, the result was amazing. I highly Recommend LA CUMBRE FLOORS. They don't have the lowest prices, but the result is worth it. I was amazed by everything they were able to achieve, thanks to their experience restoring very old and deteriorated floors.”Héctor D. · Google review
“Tony and his team at LaCumbre Floor Covering & Design are simply the best! I am am Real Estate Broker in Santa Barbara & have used Tony for my own home as well as refer him out regularly to many of my clients who are incredibly discerning and require the highest level of quality. They are all impressed! From simple carpet removal, floor refinishing, color matching, to new hardwood & manufactured floor installation, La Cumbre Floor Covering & Design has got you covered! I will continue to use and refer Tony & his team any chance I get.”Chris H. · Google review
“Tony is a magician! I hired his company, LA CUMBRE Flooring to re-do my staircase and his work exceeded my expectations. Tony pays attention to all of the details and his work is of the highest quality. His associate Jesus was also exemplary! They were very respectful and used great care while working in my house. Tony’s knowledge and expertise brought my staircase back to life! BRAVO LA CUMBRE FLOORING!”Trini L. · Google review
“When we bought our house, La Cumbre Floor Covering did an amazing job refinishing and staining the existing hardwood floors that had yellowed over the years. Tonatiuh also seamlessly repaired and patched a redwood deck in our sunroom. We appreciate his skill, professionalism and attention to detail.”Sally F. · Google review
In our own words

“I know we aren’t the best, but we always do the very best we can.”

La Cumbre Floor, replying to a customer on Google

“We know there are many other options, but we are so grateful you chose us!”
To Shannon
“And thank you so much for offering us such delicious coffee every morning, and for being so respectful and kind to me and my work crew.”
To Sheri S.
“Our success is fueled by customers like you.”
To Chris H.

We write our own replies. Read a few and you'll notice what we thank people for most: how they treated our crew. Read our replies

la cumbre Spanish for “the peak”
“We named it La Cumbre because it means the peak, and that's the standard we set: the highest level of craftsmanship, quality and design in everything we build.”La Cumbre Floor
About

Eighteen years on hardwood. La Cumbre Floor since 2023.

La Cumbre Floor Covering & Design opened in 2023, built on eighteen years of hardwood work. We're based in Carpinteria, and about 85 percent of our work is in Santa Barbara. The company is licensed and insured, and accredited by the Better Business Bureau. English and Spanish spoken.

“There's nothing quite like taking raw timber or an aged floor and turning it into the centerpiece of a home. Hardwood flooring is an honest craft, and I love every detail of it.”La Cumbre Floor’s founder
Questions

Questions people ask before we start.

If yours isn't here, see all the questions or call and ask us.

Can my floor be refinished, or does it need replacing?

Most solid hardwood can be sanded and refinished, often more than once. Boards that are eaten, rotted or worn too thin get replaced one by one. We can tell you which you have when we see it.

My floor has two different woods. Can they match?

Usually. Different woods take the same stain differently, so we tint the color until they blend. There's a Santa Barbara job with old red oak and new white oak on the color matching page.

There's hardwood under my carpet. Is it worth uncovering?

Often, yes. We remove the carpet, see what shape the wood is in, repair it and refinish it.

Do you only do wood?

Wood is most of the work. We also install luxury vinyl plank, laminate and carpet, level slabs, coat garage floors in epoxy and polish concrete. Not tile or decks.

What does an estimate cost?

Nothing. Estimates are free, and we come out to look usually within one to three days. Call or text (805) 698-9745, Monday to Saturday, 8 am to 10 pm.

What's the smallest job you'll take?

A scratch touch-up.

Contact

Call or text La Cumbre Floor. The estimate is free.

Tell us the rooms, the wood if you know it, and what's wrong with it. A photo by text helps.

(805) 698-9745
Hours
Monday to Saturday, 8 am to 10 pm. Closed Sunday. We pick up, even on a job.
Based in
Carpinteria
Serving
Santa Barbara and Ventura Counties: Santa Barbara, Montecito, Goleta, Summerland, Santa Ynez, Ventura, Ojai, Oxnard and Camarillo
Languages
English and español
Payment
Check, card, Zelle or cash